xl 30-7-10 evergreen special

HIGH IRON – ACID FERTILIZER

FOR SOIL INJECTION INTO ROOT AREAS OF PLANTS, SHRUBS AND TREES WITH HUMIC ACID

SLOW RELEASE – LOW SALT – CHLORIDE FREE – SUSPENSION TYPE FORMULA
CONTAINS: EXTRA IRON AND SULPHUR WITH CHELATE COMPLEX AND WETTING AGENTS
FOR IMPROVED ABSORPTION AND SUSPENSION..

guaranteed analysis

Total Nitrogen (N)30.00%
7.5% Water Insoluble Nitrogen
2.1% Nitrate Nitrogen
0.9% Ammonia cal Nitrogen
19.5% Water Soluble Nitrogen

Available Phosphate (P2O5)7.00%
Soluble Potash (K2O)10.00%
Sulphur (S)1.10%
Secondary Plant Foods:

Copper (Cu)0.05%
Iron (Fe)0.18%
Manganese (Mn)0.05%
Zinc (Zn)0.05%

Potential acidity equivalent to 1100 lbs. calcium carbonate per ton.
Net weight 30 lbs.

XL EVERGREEN SPECIAL 30-7-10

is for- mulated for the professional arborist. Because of its high U.F. content it does not dissolve completely, but with strong agitation remains in suspension. Therefore it should only be used in power spraying equipment with good mechanical agitation. Over 38% of the nitro- gen in XL Evergreen Special is derived from Nitroform.® This unique ureaform fertilizer releases it’s available nitrogen over the entire growing season. any not released during the first season will carry over to the following year. Nitroform® is non-leaching. Bacteria con- verts the more soluble fraction of the nitro gen so that 1/3 is released in the first 3 to 5 weeks, the balance over 6 to 12 months.

XL EVERGREEN SPECIAL 30-7-10

is for- mulated for shrubs, trees and plants that require high acid soils and extra quantities of iron. It can be injected around individual trees and plants or throughout a foundation or bed planting.

APPLICATION: SHRUBS, ROSES, SMALL BEDDING PLANTS

Injection holes should be 2 to 4 ins. Deep. Injection should begin 6 ins. out from the main trunk or stern, spaced 2-1/2 ft. apart, injection on a grid extending at least 6 ins. beyond the drip line. Apply 150 gals. to each 2000 sq. ft.

Dilution Table

Lbs. of Evergreen Special per gals. of water
15 100
30 200
75 500

Following the grid method outlined, you should inject 16 oz. of fertilizer solution at each point. Based on the 1-1/2 ft. spacing, this will apply 150 gals. of solution over 2000 sq. ft. or 75 gals. over 1000 sq. ft.

To Calibrate: We suggest that you calibrate your tree feeding needle by finding out how long it takes to inject 16 oz. of solution into a bucker. This will probably take 1 to 2 seconds, count off the seconds and use this same count and cadence while injecting the probe at each point in the soil.

FOR LARGE SHRUBS AND TREES

Injection should begin 2 ft. out from the trunk and be spaced 2-1/2 feet apart, injecting on a grid extending beyond the drip line. Apply 150 gals. to each 2000 sq. ft. following the grid method outlined, you should inject approximately 1/2 gal. of fertilizer solution at each point. Based on the 2-1/2 ft. spacing, this will apply 150 gals. of solution which contains 9 lbs. of N or 4.5 lbs. N per 1000 sq. ft. calibrate as above for 1/2 gal. of solution in bucket.

Trunk diameter rate of application: Use same dilution rates as shown in table. Apply the solution at the rate of 5 gals. per in. of trunk diameter. This is equivalent to .30 lbs. of actual N per in. using crown spread technique (concentric circles) inject the 150 gals. over 2000 sq. ft.

Space injection points at 1-1/2 ft. intervals, starting 2 ft. from trunk and extending 2 ft. beyond drip line.

Five gallons of fertilizer solution per inch of trunk diameter.Example: tree trunk 12″ times 5 gals. = 60 gals. of solution.


DOWNLOAD MSDS pdf